PIC16F19156PIC16F19175 PIC16F19176 PIC16F19185 PIC16F19186 PIC16F19195 PIC16F19196 PIC16F19197 PIC16F1933 PIC16F1934 PIC16F1936 PIC16F1937 PIC16F1938 PIC16F1939 PIC16F1946 PIC16F1947 PIC16F505 PIC16F506 PIC16F526 PIC16F527 PIC16F570 PIC16F610 PIC16F616 PIC16F627 PIC16F627A PIC16F628 PIC16F628A PIC16F630 PIC16F631 PIC16F636 PIC16F639 PIC16F648A PIC16F676 PIC16F677 PIC16F684 PIC16F685 PIC16F687 PIC16F688 PIC16F689 PIC16F690 PIC16F707 PIC16F716 PIC16F720 PIC16F721 PIC16F722 PIC16F722A PIC16F723 PIC16F723A PIC16F724 PIC16F726 PIC16F727 PIC16F753 PIC16F785 PIC16F818 PIC16F819 PIC16F84A PIC16F87 PIC16F870 PIC16F871 PIC16F872 PIC16F873 PIC16F873A PIC16F874 PIC16F874A PIC16F876 PIC16F876A PIC16F877 PIC16F877A PIC16F88 PIC16F882 PIC16F883 PIC16F884 PIC16F886 PIC16F887 PIC16F913 PIC16F914 PIC16F916 PIC16F917 PIC16F946
All VSS and VDD pins must be connected. Even if one of these pins is not connected, programming may fail.
Since NSDSP is a Low-Voltage Programmer (LVP), it can only program PIC devices if LVP configuration bit is enabled. Fresh (unprogrammed) devices have LVP bit set and therefore they can be programmed. It is impossible to disable LVP bit during LVP programming, but if the device has been previously programmed with HVP programmer, the LVP bit may have been disabled.
When brown-out is enabled with BOREN configuration bit, LVP is only possible when the VDD voltage is above the brown-out threshold.
Target Voltage Below 2.7V
If voltage is less than 2.7V programming is severely limited - it is impossible to bulk erase the device, it is also impossible to erase configuration bits, EEPROM.
NSDSP cannot detect target voltage and it assumes that the voltage is above 2.7V. If the actual target voltage is less, programming will fail. However, if you tell NSDSP that the target voltage is below 2.7V through programming software, NSDSP will use special low-voltage programming mode. In this mode, NSDSP verifies if the desired programming can be performed at voltages below 2.7V, and if it is possible (device is not code protected, configuration bits do not change or only change from 1 to 0, EEPROM is not programmed), it performs the programming. If such programming is impossible, NSDSP software will stop and show an error message.
Programming in low-voltage mode may be considerably slower. In addition, you may need to decrease programming speed to 3MHz or below.
We have measured time necessary to program and verify PIC16F19156.
|Operation||Time||Programming and Verification||1.6s||Programming only||1.3s||Verification only||0.6s|
The measurements reflect the time necessary to program/verify the entire chip, including all user programmable memory areas and very slow data EEPROM.
NSDSP firmware contains all the necessary provisions for debugging PIC16F19156 and may be debugged when debugging software becomes available.
© 2007-2020 Northern Software Inc. All Rights Reserved.